Digital Ground Resistance Tester Model 6470 
AEMC’s NEW rugged, Digital Ground Resistance Tester Model 6470 performs ground resistance, earth coupling measurement, soil resistivity and bonding tests. This direct reading tester measures from 0.01 to 99,000Ω, and is auto-ranging, automatically seeking out the optimum measurement range test current and test frequency. The adjustable test frequency (either manual or automatic) from 40 to 513Hz test voltage provides rejection of high levels of interference, allowing it to be used under difficult conditions, such as the presence of high stray currents that normally affect accuracy.
Easy-to-use and accurate — simply connect the leads, select the test mode, Press-to-Measure and read the results. Up to 512 test results can be stored in internal memory for later recall to the display or downloaded to a PC for analysis and hard copy reports with automatic fall of potential plots.
Contained in a heavy-duty field case, the 6470 is sealed against dust and water when closed.
GM40…One Timer Is All You Need! 
Grasslin Controls, a division of GE Consumer & Industrial, is proud to introduce the NEW GM40, a 40 AMP, SPDT and DPDT, 120, 208/240 or 277 multi-voltage mechanical time control with an indoor/outdoor, NEMA 3R standard enclosure. The GM40W, weekly or 7-day/”skip-a-day”, timer is also available with identical features as the standard GM40 timer. All mechanical units are available with quartz drive battery back-up.
Serviceability was a key concern of the contractors and a “user friendly” operation was essential to the end user. The real clock face and captive trippers settable on 15-minute intervals, make it easy to set the timer and its programs. The “guts” or mechanism simply pops out and snaps into an existing Intermatic enclosure with no tools required. This process is UL listed and approved for retrofit applications. A moisture resistant conformal coating has been added to the board to maximize its protection from high levels of humidity and areas of dampness.
Inside the new compact VALOX® NEMA 3R enclosure are some truly winning design innovations. Amber and green indication lights will display the timers’ cycle mode.
Responsiveness to industry demands has enabled Grasslin to produce a time control that has all the features and benefits contractors, end users and distributors wanted: it’s easy to read, easy to install, easy to set and program, easy to maintain, functionally simple yet tough and reliable.
The real clock face and captive trippers settable on 15-minute intervals, makes it easy to set the timer and its programs. The “guts” or mechanism only simply pops out and snaps into an existing Intermatic enclosure with NO TOOLS REQUIRED!
New PVC Conduit Repair System
In order to significantly reduce the time and costs associated with repairing broken conduit (a.k.a. “stub-ups”) in concrete slabs, Carlon â introduces a new, revolutionary, patented design PVC Conduit Repair System.
The Carlon PVC Conduit Repair System is a line of couplings, adapters and reamers that allow contractors to quickly and easily repair broken PVC conduits without having to chip-away and re-pour concrete, and still maintain the inside diameter of the conduit. The process is simple 1) Cut off the broken conduit; 2) Ream the ID of the conduit; and 3) Insert a coupling or adapter. A job that normally takes 20 minutes can now be done in 2 minutes or less.
For more information, visit www.carlon.com.
The NEW Arrow T72 Wire & Cable Tacker 
The NEW Arrow T72 Wire & Cable Tacker is designed to shoot UL & CUL*.
It offers large, insulated staples for faster, safer and more efficient wire installation than traditional methods! This unique tool is perfect for securing 12/2 & 14/2 NM sheathed cable and other wire up to ~1/2” (12 – 15 mm) wide.
The American-made, all steel T72 has a grooved driving blade and guide to protect the cable from being damaged. Each T72 staple has a unique high-density insulator, which further assures protection against jacket penetration. The staples have a special coating that increases holding power over three times.
The tool features a wire guide attachment to secure cable up to ½”. Remove the attachment to secure larger wires up to 19/32”. It also features Arrow’s famous easy squeeze compression handle, protective chrome plating and jam-proof mechanism.
Installers are able to save hours on the job by simply laying down wire with one hand, and operating the stapler with the other. There is no fumbling with hammer, nails and wire the old fashioned way. Installation is fast, easy, precise and efficient.
* item 721168 staples are UL & CUL listed for 14/2 NM sheathed cable
ConstructJob 
ConstructJob is a web-based project management system that allows contractors to create, manage, track, and share project documentation more efficiently, and communicate and collaborate with industry partners more effectively. Since ConstructJob is web-based, there’s no software to install, upgrade, and maintain, and your project information is accessible wherever there’s an Internet connection.
ConstructJob is now integrated with Accubid’s estimating systems, allowing you to share estimating data between the two programs. Project managers can now use an estimate as the starting point for the project.
ConstructJob consists of three optional modules: C-Job, an online project document management and collaboration system; C-Bid, a private online planroom where contractors can post up-to-date bid information, send bid invitations and updates, and upload critical bid information such as drawings, specifications, and addenda; and C-Town, an online construction community where contractors, suppliers, and manufacturers can obtain information including due dates for projects currently available for bidding.
Innovative New Raceway Offers Contractor Advantages 
Designer Series™ steel raceway from Wiremold/Legrand speeds installation by reducing or eliminating field cutting, avoiding on-wall obstacles, and accepting all standard devices. 4000 Designer Series raceway also features an optional downward facing configuration for receptacles and data jacks that improves connection reliability and creates more space inside the raceway to meet cable bend radius requirements.
The modular design of 4000 Designer Series raceway minimizes the number of cuts required during installation, and the scored base makes cutting easy when needed. Unique adjust-to-fit raceway couplings allow up to 4" of lateral movement so the base can be “stretched” or “compressed” to fit a given space and/or to align mounting holes with studs. The channel divider is integral to the base rather than a separate piece, saving additional time, and obstacle avoidance fittings allow the raceway to bypass existing conduit or small raceway on the wall.
Werner Introduces the Electrician’s JobStation™
With integrated features uniquely designed to simplify the electrician’s tasks, Werner’s Type IAA Electrician’s JobStation™ features built-in accessories to make jobs faster, easier and safer.
The top features customized slots and bins to hold tools, a built-in scale for measuring and cutting conduit, and the ToolLasso™ Bungee System to hang heavy tools. An integrated conduit holder, hacksaw hook and safety shield on the rails make cutting simple and secure. The wire spool holder brackets organize wire spools and make wire pulling effortless. See www.wernerladder.com/oldblue/ for details.
Litheon 10.8V Pocket Driver (PS20-2)
The 10.8-volt Pocket Driver is an ultra-compact drill/driver capable of driving an 
astounding 100 3” screws on a single charge and drilling up to ½” diameter holes. Big Power, Small Package – Pioneering a new power tool category, the Pocket Driver measures approximately 6” square and weighs less than 2-lbs. While the tool literally fits into a pocket or tool belt pouch, it is also capable of performing 80% of the applications other professional higher voltage cordless drill/drivers twice its size and weight. Based on the traditional pistol grip design, this tool truly redefines the perception of a professional drill/driver.
Greenlee’s Ultra Tugger ® 2: One Person to Pull One Ton with One Puller 
Greenlee’s new 2000-lb Ultra Tugger ® 2 cable puller provides the pulling force, speed, and mobility for one person to pull one ton with one puller. The new USA made lightweight UT2 is intended for quick set up and teardown by utilizing Greenlee’s Quick Latch system, and its two-speed hi-torque integral motor is designed specifically for cable pulling applications.
The new UT2 is developed for one person to use. It weights only 67 lbs, has rugged wheels for easy mobility, and can be folded up and lifted by one person, either onto or off of a truck.
To set up the UT2, just attach the telescopic boom and pivoting elbow to the conduit using the Quick Latch, adjust the boom angle and length to the particular pull and the UT2 is ready to go – usually in less than a minute. The UT2 easily attaches to any size conduit 1” and larger and there is no need to unscrew or remove the locknut on the conduit and there are no loose parts to contend with.
Greenlee’s patent pending Quick Latch system matches up to the threads of any size conduit and holds securely on the conduit when the clamp is tightened using the large locking knob. There’s no drill to attach. To make a pull, just plug the UT2 into a 15 amp circuit and turn it on.
The UT2’s double capstan provides two different speeds while the integral motor is specifically designed for the pulling application at hand. Gear ratios are also built-in to the UT2 to ensure long-lasting performance and avoid overloading. The hi-speed capstan is for loads 1000-pounds and less. The low-speed capstan is designed for loads of up to 2000-pounds. The UT2 can readily pull:
- 3 X 500 kcmil cable, 500 feet with two 90 O bends;
- 3 X 500 kcmil cable, 250 feet with four 90 O bends; and
- 8 X 4/0 AWG, 300 feet with three 90 O bends.
For added safety and convenience, an on/off switch and a circuit breaker are located right on the motor and a right angle sheave keeps the user out the direct line when pulling the rope. Greenlee recommends using 5/8” polyester multiplex rope with the UT2.
For more information, visit www.greenlee.com.
Energy Costs: You Can’t Manage What You Don’t Measure
E-Mon D-Mon® submeters and RightEnergy™ software provide the tools your customers need to measure and manage energy costs in new and retrofit applications.
- Monitor anything from a single-phase circuit to an entire building.
- Low installed cost. Quick & easy installation without power interruption.
- Read meters remotely and allocate costs with RightEnergy software.
- Wireless, Ethernet and ModBus communications available.
Ask about the new E-Mon D-Mon Contractor Certification Program!
AlumiConn™ Aluminum to Copper Lug 
King Innovation’s AlumiConn™ Aluminum to Copper Lug provides a superior pig-tailing method with its secure, mechanical connection of conductors. Pre-filled with silicone, which reduces corrosion and oxidation of the connection, AlumiConn is designed as a tin-plated lug with nickel-plated compression screws. Featuring three ports that eliminate intermixing of conductors, the connection runs approximately 25 ° F cooler than purple twist-ons, providing more safety with lower temperature, lower resistance, and longer-term reliability. UL 486A – 486B listed to meet U.S. and Canadian specifications, AlumiConn is certified for aluminum to copper (AL-CU) connections as well as copper to copper and aluminum to aluminum. Versus other methods for replacing aluminum wiring systems, AlumiConn offers a superior solution for replacing AL-CU and aged electrical wire systems. The one-piece lug installs quickly and easily, saving electrical contractors time and money, providing a more cost-effective alternative for retrofitting splices. For more information, visit www.alumiconn.com .
The Most Award-Winning Timekeeping System in Construction
The JobClock ® time and attendance system eliminates inaccurate handwritten timecards. The weatherproof, battery-powered JobClock locks down anywhere. Workers clock in and out with green and red “Keytabs” carried on their keyrings. With additional colored Keytabs, you can also track travel time and cost codes.
Using a Palm Pilot, time records are collected from each JobClock prior to payroll and transferred to a PC. With TimeSummit ® software, you get accurate timecards and detailed reports for employees, jobsites, and cost codes, along with overtime, rounding, and lunch breaks. Additional AccountLinx™ software transfers the records to many accounting and payroll programs. Payroll preparation is fast and easy!
For workers on the go, try PocketClock, designed for service work and/or using dozens of cost codes. Each worker clocks in on a Palm using PocketClock where they’re prompted to select the jobsite and cost code. Supervisors have additional site management tools and can easily clock in an entire crew.
Introducing McCormick’s ABS Product Line 
McCormick Systems’ award winning line of estimating products now offers a complete line of products designed specifically for ABS Contractors. Whether your business focus is Voice, Data, Fiber Optics, Fire Alarm, Audio, Video, Paging, CCTV, Card Access, Surveillance, Low Voltage, HVAC Controls, Nurse Call, Cable Tray, Security, Intercoms, Lightning Protection, Electrical, or a combination of them all, McCormick has the estimating package to satisfy your needs.
Bridgeport Fittings Introduces Signaling Products
Bridgeport Fittings, Inc. is introducing an extensive line of audible and visual signaling products for the residential and commercial markets. The line – consisting of over 160 SKUs – will come to market under the Bridgeport Switch™ brand.
The introduction supports Bridgeport Fittings’ long-term strategy to transition its product portfolio beyond cable and conduit fittings to electrical construction materials. This commitment encompasses several new product categories that the company plans to introduce in the next few years.
The Bridgeport Switch brand comprises two major categories of signaling products: audible signals and visual signals. The audible signaling line includes bells and buzzers, vibrating horns, builders’ chimes and chime kits, door switches, low voltage push buttons, door openers, and transformers. Visual signals in the line include the four main types: steady beacons, flashing beacons, rotating beacons and strobes.
For more information, visit www.bptfittings.com.
Pre-assembled Wiring Solution 
ProtectConnect’s Pre-assembled Wiring Solution is ideal for institutions like hospitals, schools and universities where safety is the main concern. It is the only product that, once installed, safely conceals all wiring and live current.
The solution comes pre-assembled with a pre-wired module, an adjustable mud ring, adjustable far-side support, side-mount bracket, eccentric knockouts, increased box capacity and attached cover plate. At trim, any grade of ProtectConnect device module can be installed with no wiring at all. It’s fast, easy and safe for anyone to complete trim or do a simple switch or outlet replacement. The solution’s pre-wired module eliminates the chance of electrical shock and drastically reduces the chance of code or other safety violations caused by wiring mistakes.
Lumière Rio Architectural Step Lights 
Lumiere has introduced a new family of architectural step lights offering durability, performance and aesthetics for commercial, retail and residential applications. Called the Rio™ Series, the petite step lights are available in 5 ” or 7 ” round or square forms, and feature several fascia designs and lamp options including LED.
Rio ’s available models/fascia designs include: Open with diffused lens; cross/guard with diffused lens (pictured); eyelid with diffused lens; and Louvered with clear lens. The low profile, transitional styling features no visible fasteners and provides seamless integration with wall types and architectural styles of all kinds.
Modular design elements facilitate fast, foolproof installation in drywall, concrete pour or brick/masonry. The series is available in multiple lamp options including Low Voltage Halogen, Metal Halide, Compact Fluorescent and LED.
Designed for both indoor and outdoor applications, the series features durable, corrosion-resistant die-cast aluminum alloy construction. All models are IP68 rated and ADA compliant.
For more information, email: talktous@cooperlighting.com .
Megger MIT400 Series 
Megger introduces a family of new insulation testers that meet the most stringent requirements for installation, maintenance, service and repair in the electrical, power and telecommunications industries. The units conform to IEC1010-2 for Category IV 600 V applications. The instruments feature Megger's patented dual digital and analog arc displays showing both measurement result and the actual test voltage being delivered simultaneously.
The new MIT400 Series of testers feature adjustable insulation test voltage providing 250 V to 1000 V or 50 V to 1000 V. A "special applications" instrument (Model MIT40X) offers test voltage from 10 V to 100 V in 1 V steps.
StarLite, RF wireless lighting control, provides robust central lighting control without expensive remodeling. Using radio frequency technology and existing electrical wiring, StarLite easily controls up-to 96 devices, 288 buttons and up-to100 lighting scenes, including one-button “vacation/alert” and “all on/all off” modes. There are 512 dimming levels that can be preset for every load, and a pleasant “soft on/soft off” function. CentraLite’s open architecture allows easy integration with other home-automation systems.
StarLite comes with intuitive configuration software. Keypads report internal temperature, power consumption, RF signal strength and light level to the base station. Performances can be viewed and analyzed using CentraLite’s PC software. Upgrades to the system can be downloaded, without replacing chips. StarLite retains its programming in multiple locations, so there’s never a risk of losing settings even if a dimmer is accidentally damaged and must be replaced. StarLite provides a robust, reliable system that is affordable, easy-to-install, and easy-to-use.
PhaseTec™ Digital Power Conditioners 
The future in protecting sensitive electrical equipment has arrived with PhaseTec™ digital power conditioners. Silicon-based power switching technologies offer superior performance compared with traditional transformer and filter solutions for power conditioning applications. Rising costsof steel and copper along with significant advances in power switching now make double-conversion power conditioning as affordable as transformer based solutions.
PhaseTec™ digital power conditioners utilize the latest advances in power switching technology to protect sensitive electrical equipment operating in even the harshest power quality environment. The double-IGBT conversion design converts the incoming AC power to DC, then regenerates clean, regulated AC power, totally isolating the load from the AC mains.
Previously, the only way to get the protection of double-IGBT power conditioning was to employ a double conversion on-line UPS. PhaseTec™ provides the ultimate in power conditioning without the expense and maintenance of batteries.
Single-phase models are available from 7 to 20 KVA.
For more information, visit www.phasetechnologies.com.
Alber BDS-40
Designed for UPS battery cabinets, BDS-40 is the perfect choice. With the monitor mounted on top of the cabinet and cables with each connection point identified to battery, installation is easy.
It monitors all batteries in one cabinet. BDS-40 makes hard-to-interpret data understandable. Problem batteries are flagged by sending alerts as soon as abnormal conditions are detected. The software analyzes data and suggests the best course of action.
A patented internal DC resistance test method is used. BDS-40 lets you "look inside" and assess the battery’s true state of health. It tests the condition of each module by performing a proactive resistance test - the most reliable indicator of battery performance. Measurement technology is the most important consideration when selecting a monitor. The Albér DC resistance test method is not affected by ripple and thus provides data that is repeatable and reflects the true condition of the battery.
New Arm Lengths Added to Heavy Duty Nonmetallic Cable Rack Line 
Underground Devices has recently added 3 new arm lengths to the Heavy Duty Nonmetallic Cable Rack line, bringing the total to seven different sizes, ranging from 3” to 20” in length. In addition to these new arm sizes, two new stanchion lengths on 12” and 24” have also been added to the line.
Underground Devices nonmetallic cable racks are a high strength, durable and non-corrosive option for all manhole projects. Nonmetallic cable racking will not rust or corrode and bonding and grounding of nonmetallic racks is not required. Cable insulators are not needed with nonmetallic racking.
Kohler’s MPAC 1500 Transfer Switch 
The new Kohler MPAC 1500 automatic transfer switch allows complete monitoring and security restricted control either locally (at the unit) or remotely (using a variety of standard communications protocols), and allows for a simple, integrated interface with the organization’s power system. It also monitors, stores and is capable of downloading (using USB storage device) full maintenance, event histories and settings to view a complete picture of the standby power system. Security has been improved with this new product, allowing for multiple passwords to offer the tightest degree of security to match the installation requirements.
All Kohler transfer switches will include this new advanced controller that also features a very flexible design to provide the customer a platform to accommodate future power system adaptations.
The MPAC1500 utilizes complete electrical monitoring to ensure the source of power will provide the correct electrical parameters to critical loads on the transfer switch.
Monitoring and changing parameters to meet the exact requirements are quickly and easily made through the 4x20 LCD screen using dynamic programming push buttons. Uploading and downloading data is easily performed with an industry-leading USB flash-memory interface.
The Work-n-Wagon Work Station
The Work-n-Wagon is a truly versatile wor
k station. It is a mobile print table with shelves for material storage and the bottom rack can be used for conduit storage. It can also be used as a portable work bench to prefab parts, assemble fixtures or other similar projects.
The Work-n-Wagon provides a solution to many of the problems crews encounter on job sites every day. A typical print table is usually constructed from plywood found laying around (most likely the search for the lumber and the construction process takes place on your time), is heavy and cumbersome to move around, (because it doesn’t have wheels) and is normally torn up by the time the job is over. The same thing goes for most jobsite work tables. With a Work-n-Wagon, you’re covered. You will have a mobile print table and work station, with the added benefit of material and conduit storage.
Real Time, Constant Thermal Monitoring of Your Electrical Switchgear and Critical Components 
ExerTherm’s exclusive, non-contact passive IR thermocouples are permanently mounted in your electrical cabinets. They require no calibration and have an MTBF of 1,000 years. No need to open the cabinets just to get a “snap shot” for one moment out of the year. ExerTherm offers 7 x 24 real time monitoring and alarming, as well as trend data for true predictive maintenance and a complete picture. Only open up cabinets when you know you need to. ExerTherm can be stand alone, or integrated into over 450 BMS / protocols. Perfectly suited for OEM or retrofit. For more information visit, www.psc-exertherm.com.
F26D Line of Fans Offer Low Sound Levels 
Krenz & Company has been the industry leader in transformer cooling fans for over 75 years. The Krenz reputation of quality and service has made their line of fans the standard fan choice for customers around the world.
Many utilities these days are specifying transformers with low sound levels. Krenz’s F26D line of fans is designed specifically to meet the transformer industry’s need for low-sound level fans while still maintaining the high-volume airflow needed to properly cool the transformer.
The unique dual-blade F26D fan is able to achieve significant airflow while maintaining the low-sound level utilities are looking for. This performance, along with the legendary reliability, service and efficiency inherent in all of the Krenz products make the F26D a perfect choice for keeping transformers cool and extending their life and/or increasing their capacity.
For more information, visit www.krenzvent.com.
Connect Generators with the InterLock Kit
Connect portable and standby generators to home pa
nels with the InterLock Kit. Safe and easy-to-use, the InterLock Kit is designed to provide contractors and home owners a low cost alternative to a transfer switch. The InterLock Kit is a safe and legal device that allows users to connect their generators to existing panels for quick and convenient use of all original circuits. The InterLock Kit retrofits to any existing panel and requires no additional wall space. Listed to UL Standard 67, the InterLock Kit meets NEC article 702.6 and NFPA 70 requirements. The InterLock Kit is a much-needed product that will save your business time and increase over-all sales. Make more money today by offering your customers the InterLock Kit. Generator InterLock Technologies offers same day shipping on all 30 models. For more information, visit www.interlockkit.com.
Uraseal’s Shake N’Seal™
Uraseal’s Shake N’Seal™ electrical splice products are a fast and economical solution for encapsulating buried splices. UL listed submersible, these kits provide a permanent seal that is 100% watertight. This encapsulant is packed in a plastic tube with the two-part product separated by a plastic wafer. The tube is also enclosed in a barrier mixing bag so that there is no mess if anything happened to the tube while mixing.
Once you have completed your splice and are ready to use the product, just flip the wafer, shake for the required amount of time (approximately 30-60 seconds depending on temperature) and then either cut the crimp of the tube and put the splice in the encapsulant tube, or use one of the closures provided with the ES200SV or ES1150 kit.
For more information, visit www.shakenseal.com.
Versa-Power Ceiling Column
The PG LifeLink Versa-Power Ceiling Column was introduced in 2006 with improved design and versatility. The Versa-Power Service Column is mounted to the ceiling to keep it in close proximity to the operating table, providing simple access to electrical services, medical gasses and other utilities. The columns are installed in locations accessible to anesthesiologists and can be specified to match ceiling heights. There are no cords hanging across the room or on the floor.
The system features include the option for isolated or grounded power. 120 or 208 volt receptacles can be used. Full-length removable panels provide easy access during installation and maintenance. The optional connections include oxygen outlets, air outlets, other gas outlets, vacuum bottles, power outlets, ground jacks and nurse call. The complete stainless steel design adds durability and ease of cleaning.
For more information, visit http://www.pglifelink.com.
CT20 Continuity Tester Pro 
Extech’s new CT20 Continuity Tester Pro is a unique and evolutionary test instrument, unlike anything on the market today. This product features the unique capability for single-person remote operation for wire and cable identification, continuity checking and polarity verification. The Continuity Tester Pro is the perfect tool for electricians, cable TV and audio system installers, alarm technicians, auto repair technicians, and do-it-yourself homeowners.
The CT20 is a two part system, consisting of the Master Continuity Tester for local continuity testing, remote wiring identification and detection and “shorts” on long cable runs along with a unique two lead, bi-color (red/green) LED probe for remote single-person operation when identifying cables, verifying polarity or labeling long distance wire/cable runs. This combination allows a single user to identify up to three wires or cables at a time, with only one trip to the other end of the wire or cable location.
IntelliBid and PowerSuite Offer a Powerful Solution for Electrical Contractors
ConEst Software Systems offers a complete contractor management and bidding software system with IntelliBid™ Estimating Software v5.1 and the PowerSuite™ set of solutions including BidTrac™, JobTrac™, T&M Billing™, and Electrical Formulas™. ConEst’s flagship estimating software, IntelliBid v5.1, continues to set itself apart from other mainstream programs with the company’s latest release of the program, which includes a database with over 70,000 electrical, low voltage, and structured cabling materials. PowerSuite electrical management solutions include BidTrac which keeps estimates organized by storing all bid data; JobTrac which gives contractors control of electrical projects by tracking change orders, alternates, submittals and all correspondence, purchase orders, AIA billing and job costing; Electrical Formulas allows contractors to perform electrical calculations and lighting design while simultaneously updating their estimates; and T&M Billing and Dispatch Manager providing service management software for scheduling work crews, generating work orders and processing invoices.
Generac’s New 16 kW Standby Generator 
The 16 kilowatt automatic home standby generator from Generac Power Systems is the highest output air-cooled generator ever made for the residential market. This new model, which operates on natural gas or liquid propane vapor, is powered by a 990 cc OHVI® (Overhead Valve Industrial) four-cycle engine, designed and manufactured by Generac. The generator is enclosed within a weather protected, sound attenuated enclosure featuring Generac’s Rhino-Coat™ textured paint for extra corrosion protection. An aluminum enclosure is offered as an option.
Generac’s industry exclusive Quiet-Test™ feature operates the generator at a slower speed during its weekly exercise routine for reduced sound output, making it as quiet as a central air conditioner. Under full load, the unit is engineered to operate more quietly than air-cooled models from other manufacturers, making it among the quietest in the industry.
Generac’s high output 16 kW generator has sufficient power to run a 4 or 5 ton air conditioning unit, plus a 3 ton AC and numerous other circuits. It provides whole house power at a very competitive price.
Pass & Seymour/Legrand® Offers One-of-a-Kind Horizontal
Steel and Wood Stud Boxes
Pass & Seymour/Legrand’s innovative Horizontal Steel and Wood Stud Boxes are ideal wherever space is at a premium. Meant for use with 1/2” or 5/8” wallboard, the Boxes accept eleven #14, ten #12 and nine #10 wires, and the large 22.5-cubic-inch volume makes installation easy. A bracket countersink allows for #8 wafer head or dry wall screws with minimal wallboard bow. The Height Site alignment guide and box levelers center the box and the device at a right angle with the stud. One stabilizer leg and a side stabilizer ensure device rigidity, and the Boxes easily accommodate dimmers and GFCIs. The Horizontal Boxes eliminate the time, energy and frustration of constructing phantom studs, and they work well in special areas, such as below kitchen counters. The Boxes are classified for 2-hour wall and ceiling fire resistance. P&S is the only manufacturer of Horizontal Boxes.
The AeroDome™ 1000-watt Area Light
In response to the increasing demand for a higher wattage area light, Ruud Lighting has created the AeroDome TM, a 1000-watt area light. The AeroDome is available in a Type III, Type IV and Type V optic and meets IESNA Full Cutoff Classification. Its rugged one-piece, die-cast aluminum 25” wide by 14.5” deep housing accommodates 250- to 1000-watt PSMH, MH and HPS lamps. Mountings include Side-Arm or Post-Top. Both feature an integral one-piece, field-replaceable electrical component ballast module with a quick-disconnect design for ease of installation and long-term serviceability. The high-impact, clear tempered glass lens secured to the die-cast aluminum door frame features a high-temperature silicone gasket that seals the lens from water and insects. The lens assembly features a tool-less, quick-release mechanism for easy maintenance. The AeroDome features an exclusive Colorfast DeltaGuard TM finish with ultra-durable powder topcoat and is covered by a 7-year warranty.
Hioki Model 3197 Power Quality Analyzer
Hioki is proud to announce the release of the model 3197 Power Quality Analyzer. This portable ergonomically designed hand held unit with its built-in one touch “QuickSet” feature allows for easy use by both the most experienced PQA professional, as well as the most novice of users. The 3197 multi-functions include the ability to monitor Inrush Current, Voltage Swells, Voltage Dips, Transients and Interruptions. Additional features include the ability of measurement and recording of Power, Power Factor, Active/Reactive Energy, Demand, Load Changes (with Graphic Display), Voltage and Current on 1P2W to 3P4W circuits. The easy to read 4.7” color STN LCD display, rubber case Grip, 4MB internal memory, 125 day recording capability, 2.0 USB interface connection, 6 hours of continuous use on a single recharge, and PC application software, complete this powerful low cost PQA package.
